Wayne-dalton 320 Bedienungsanleitung PDF herunterladen

Wayne-Dalton Corp. Upward Acting Sectional Doors

Model 320 Wood Flush Specifications

1.01 Work Included

A) The sectional doors will be Wayne-Dalton Model 320 as manufactured by Wayne-Dalton Corp.

1.02 Related Work

A) Opening preparation, miscellaneous or structural metal work, access panels finish or field painting,

field electrical wiring, wire, conduit, fuses, and disconnect switches are in the Scope of Work of other

divisions or trades.

2.01 Door Sections

A) Will measure a full 1-3/4" thick, constructed of west coast Hemlock, Sitka spruce or equal frame

with interior or exterior surfaces of semi-tempered 1/8" hardboard, pressure-bonded to both sides with

type 1 waterproof glue. Rabbeted weathertight joints are provided throughout. (Optional rubber

astragal is available to seal against floor and bottom of door and protect wood from moisture).

Sections are available as standard primed (not primed as specified). Core material will be 1-1/2"

polystyrene insulation - 6.40 R-value.

2.02

Track

A) All track, vertical mounting angles and brackets will be commercial quality steel minimum 16 ga.

thickness, hot-dipped galvanized. Track is (2") (3") standard or as specified. Vertical track to be

graduated providing wedge type weathertight closing with (bracket mounting for wood jambs)

(continuous angle mounting for wood jambs) (continuous reverse angle mounting for steel jambs), and

fully adjustable to seal door at jambs. Horizontal track will be reinforced with continuous angle of

adequate length and gauge to help prevent deflection.

2.03 Hardware

A) All hinges and brackets will be made from hot-dipped galvanized steel. Track rollers will be case

hardened inner steel races with 10 ball (2") (3") rollers.

2.04 Counterbalance

A) Springs will be torsion type, low-stress, helical wound, oil tempered spring wire to provide minimum

10,000 cycles of use - or meet specified cycles - on continuous steel shaft; (solid CRS). Spring fittings

and drums for the torsion unit will be made of die cast, high strength aluminum. Pre-formed

galvanized steel aircraft cable will provide a minimum of a 5:1 safety factor. (Long life springs of

25,000, 50,000 or 100,000 cycles may be specified and are recommended for high usage doors).

2.06 Lites

A) (Glazing options are available).

2.07 Locks

A) Will engage right-hand vertical track and utilize an interior side lock. (Standard size rim cylinder

single lock bar or 2" track only double lock bar that engages both vertical tracks are available).

2.08 W

indload

A) Per DASMA 102-2003 and as required by local codes.

PART I- GENERAL

Note to specifiers: Words in parenthesis indicate options that need to be specified.

PART II- PRODUCT

08360/WAY - BuyLine 0261

1 2

Inhaltsverzeichnis

Seite 1 - PART II- PRODUCT

Wayne-Dalton Corp. Upward Acting Sectional DoorsModel 320 Wood Flush Specifications1.01 Work IncludedA) The sectional doors will be Wayne-Dalton Model

Seite 2 - PART III- EXECUTION

2.09 Options A) Chain hoist or motor operator.3.01 InstallA) Install the doors in accordance with Wayne-Dalton Corp. instructions and standards. Insta

Kommentare zu diesen Handbüchern

Keine Kommentare

Wayne-dalton 320 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Möbel Wayne-dalton 320 herunter. Wayne-Dalton 320 User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Möbel Wayne-dalton 320