Wayne-dalton THERMOMARK 5155 Bedienungsanleitung PDF herunterladen

Wayne-Dalton Corp. Upward Acting Sectional Doors

Thermomark

™

5155 Specifications

1.01 Work Included

A) The sectional doors will be Wayne-Dalton (Thermomark

™

5155) as manufactured by Wayne-Dalton

Corp.

1.02 Related W

ork

A) Opening preparation, miscellaneous or structural metal work, access panels finish or field painting,

field electrical wiring, wire, conduit, fuses, and disconnect switches are in the Scope of Work of other

divisions or trades.

2.01 Door Sections

A) Door sections will be of steel/polyurethane/steel sandwich type construction to include a thermal

break and have a calculated "R"-value of 10.96, in accordance with industry guidelines. The exterior

skin of structural quality, .015" (min.) hot-dipped galvanized steel, embossed with pebble grain texture

and features ¼" wide pinstriping, will be factory-finished with baked-on polyester primer and white

polyester finish coats. The interior skin will be .015" (min.) structural quality, hot-dipped, galvanized

steel, factory-finished with a polyester primer and white polyester finish coats. Hinge locations have 20

ga. continuous back up steel strips for hardware attachment and "cut-down" capability. Ends of

sections have full-height 18 ga. (min.) (16 ga. available) hot-dipped galvanized steel end caps. The

void between the interior and exterior skins will be completely filled by foamed-in-place CFC free

polyurethane core. Bottom astragal is a two-piece "bulb" shaped astragal to be attached to the

bottom section. Between section joint seal is standard.

2.02 Track

A) All track, vertical mounting angles and brackets will be commercial quality steel minimum 16 ga.

thickness, hot-dipped galvanized. Track is (2") (3") standard or as specified. Vertical track to be

graduated providing wedge type weathertight closing with (bracket mounting for wood jambs)

(continuous angle mounting for wood jambs) (continuous reverse angle mounting for steel jambs), and

are fully adjustable to seal door at jambs. Horizontal track will be reinforced with continuous angle of

adequate length and gauge to help prevent deflection.

2.03 Hardware

A) Hinge & Roller Assembly - All hinges and brackets will be made from hot-dipped, galvanized steel.

Track rollers will be case-hardened inner steel races with 10-ball, (two-inch roller) (three-inch roller).

All factory authorized attachments will be made at locations indicated and reinforced with additional

backup plates.

2.04 Counterbalance

A) Springs will be torsion type, low-stress, helical wound, oil-tempered spring wire to provide minimum

10,000 cycles of use - or meet specified cycles - on continuous steel shaft; (solid CRS). Spring fittings

and drums will be made of die cast, high-strength aluminum. Pre-formed galvanized steel aircraft

cable shall provide a minimum of a 5:1 safety factor. (Long life springs of 25,000, 50,000 or 100,000

cycles may be specified and are recommended for high usage doors).

PART I- GENERAL

Note to specifiers: Words in parenthesis indicate options that need to be specified.

PART II- PRODUCT

08360/WAY - BuyLine 0261

1 2

Inhaltsverzeichnis

Seite 1 - 5155 Specifications

Wayne-Dalton Corp. Upward Acting Sectional DoorsThermomark™5155 Specifications1.01 Work IncludedA) The sectional doors will be Wayne-Dalton (Thermomar

Seite 2 - PART III- EXECUTION

2.05 Weather StrippingA) (Optional factory- installed top section header seal or field-installed jamb/perimeter seals are available).2.06 LocksA) Lock

Kommentare zu diesen Handbüchern

Keine Kommentare

Wayne-dalton THERMOMARK 5155 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Möbel Wayne-dalton THERMOMARK 5155 herunter. Wayne-Dalton THERMOMARK 5155 User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Möbel Wayne-dalton THERMOMARK 5155